Hi, long time since I last posted this is my newest find a Petromax 826 – few things I wanted to ask First is the hood/ventilator is original? Is the wheel is original? Can you help me date this lantern the logo has the E inside the G other then that the model number is engraved on the fount above the Petromax name Thank you for any additional info
Petromax 826
-
-
hi
yes the wheel is orginal, this ist a early pertinax wheel from petromax.
sorry for my bad english
-
Thanks for the answer
Is the hood/vent acurate too?
I also have a butterfly type fuel cap is that also correct?Thanks
-
Hello,
the hood looks not correct.
can you make a photo from the top?Greetings
Hartmut
-
Zitat
Original von steelkingdom
.....
Can you help me date this lantern the logo has the E inside the G other then that the model number is engraved on the fount above the Petromax name
.....
the E inside the G shows that at least the fount must be before the 1943 -
Hartmut:
Here is an image from the top dose this help?
Can you or any other post a picture of the cirrect vent (in case this is not correct) -
Hello,
congradulations.
This hood is correct and really old.
Build in the early 1930'th.Greetings
Hartmut
-
Hi Thanks for the info I therefore can estimate the lantern to the 1930~1943 I have a problem I could use help for The check valve on the Petromax is stuck - and I found out that it has a different check valve then usual - not the one like the 829 that could fit a screw driver but one similar to the image I attached How do I take it out? - Can it be replaced by the modern one? Another question is can I convert the lantern to 500CP by using a 500CP nipple and needle? Thanks a lot Another image of the Check valve added (thanks to simon.w)
-
The valve is the same you found in Petromax and BAT stoves.
It gives a tool to remove.
It can be replaced by the modern one, that's no problem.
Also you can use a 500CP nozzle and needle to have a 500CP lamp.Greetings
Hartmut
-
Hello steelkingdom,
you can find the tool in the shop.
http://www.starklichtlampe.de/german/images/valvespanner.jpg
-
Hi all thanks for the answers
Ohm:
Can you point me to the web page for the tool in the shop
so I could add it to the shopping cart - I search for it but could not find it anywere -
hi
look for classic stove parts in the german shop.
the part have the name pumpenventilschlüssel.
mfg andreas -
Thank you for the pointer
-
Thanks all for the help
I forgot about this thread and I owe you this image: -
Hello,
Your lamp looks great, and fine to see that restoring such and old one into working order is possible!
I have earlier manged to buy a pre-war large Petromax in excellent condition
(see http://www.pelam.de/petromaxfo…x-826,-aber-wie-alt-.html)
but last week I found yet another one "oldie" - from closer than I could ever expect... this 821 was forgotten at my late grandparents' summer cottage, buried among abandoned stuff in a shed. A historical Petromax with a family history, not bad! It's here just in the condition as it was when found, I will start working with it when my holiday begins. I have tested that the cleaning rod and pressure pump work, but there seems to be a minor (invisible) leaking point under the tank. Unfortunately the original glass is broken. This one has a slightly different looking hood, note the smaller ventialtion holes, but there are two screws on the top like in yours (a 30´s feature, if I'm not mistaken). -
very nice find of a very looked for lantern
waiting to see the "after" pictures -
Hello, Doron,
Here is a picture after first cleaning session. Quite a bit more shiny, but apparently the nickel coating is more or less corroded here and there, I am not sure if anything could to be done to get rid of those matt looking patches without causing more damage than good...
-
Still a very nice find
now we would like to see it burning -
Zitat
Original von Doron Papo
Still a very nice find
now we would like to see it burningThanks for the compliments and lots of optimism
In one previous posting I wrote that there must be a leak in the bottom of the tank. Following a tip given in another discussion, I sunk the tank into water and found the exact spot: it was in the seam between the bottom plate and the edge of the fount. I have only a low-powered soldering iron (25W) which is not a very good tool to handle anything this big, but I succeed to put some solder over the leak, and it seems to be air tight now.
Unfortunately I found another leak, too, and this one is in a more difficult place (at least to fix without aesthetic damage to the lantern): see the following picture - the bubbles are coming from a microscopic hole halfway the side of the fount. Does anyone have a good tip what to do with this?
-
Zitat
Original von Finnmax
picture - the bubbles are coming from a microscopic hole halfway the side of the fount. Does anyone have a good tip what to do with this?I got an idea; perhaps I could pour about a large spoonful of liquid acrylic alkyd varnish (or something similar) into the tank and then place the tank in such position that most of the varnish will settle over the area where the almost invisible hole is, forming a hopefully strong enough cover to stop the leak when the varnish hardens. On the other hand, if the varnish will not stick properly to the brass, or will be dissolved over the time by the chemical effect of being in contact with the kerosene, lumps of it may travel to entirely wrong places and cause problems there...